AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Black screen parallels desktop mac4/6/2024 ![]() The rest of the installation is unattended and will install SteamOS.You will have the option to change the default disk partitioning.Selected your preferred language, location, and keyboard layout.Selected "Expert install" from the menu.When the backup completes, select "reboot" to boot into your freshly installed SteamOS.After Steam finishes installing, your system will automatically reboot and create a backup of the system partition.Once you are connected to the internet, close this UI and Steam will install itself. Discussion in Parallels Desktop on a Mac with Apple silicon started by RyanM37, Oct 13, 2022. If you do not have an internet connection (for instance, if you need to connect to a WiFi access point) you will get a popup telling you this.Ĝlose the popup and you will get the network configuration UI where you can set up your network. Home Forums > Parallels Desktop for Mac > Parallels Desktop on a Mac with Apple silicon > Steam games not working. If you have an internet connection, Steam will automatically install itself. At this point an internet connection is required. After installation is complete, the system will reboot and automatically log on and install Steam.The rest of the installation is unattended and will repartition the drive and install SteamOS. ![]() Selected "Automated install (WILL ERASE DISK!)" from the menu.If there is no UEFI entry, you may need to enable UEFI support in your BIOS setup. Make sure you select the UEFI entry, it may look something like "UEFI: Patriot Memory PMAP".(usually something like F8, F11, or F12 will bring up the BIOS boot menu). Boot your machine and tell the BIOS to boot off the stick. Put the USB stick in your target machine.Unzip the SteamOS.zip file to a blank, FAT32-formatted USB stick.I am not sure how diagnostics are run and what they look at, but I am sort of at a total loss.WARNING: Both installation methods will erase all content on the target computer Automated Installation My other concern though is the failure to access the drives. However, it seems as though this is my wildcard and I do not need it. I do not need Parallels as I can just dual boot although it would be a cool feature. When I go to install parallels on the Lion drive, my screen goes black when trying to access Windows. I am a total noob and at this point am a little afraid to get this thing going again.įrom my analysis of the situation, I get Lion and Windows up an running. I am not sure which one (Lion or Windows) and he was only performing a hardware diagnostic analysis (no software). Since I was having the same issue with my previous motherboards, could there be something that is messing with the motherboards controller? Or am I the lucky one that got (2) faulty motherboards? The tech also said that he was having issues accessing both of my spin drives and one of my SSD drives. I am now moving to my 3rd motherboard, the diagnostics showed that the controller for the motherboard was faulty. I have been at this for a bit now and have been getting help from Micro Center on analyzing my hardware. Please keep in mind that I am a noob at this sort of thing so bear with me if I have done something stupid. Did my motherboard die? Did my graphics card and on board graphics get fried? Any thoughts? What should my next steps be? I am not sure what to do from here or what has happened. Turned it off and came back 20 mins later (no luck) Turned all power off, unplugged and cleared CMOS (no luck) Unplugged all drives except for the Lion install (no luck) Unplugged graphics card and tried to use the onboard graphics - both DVI and VGA (still a black screen and no splash screen) ssues.html) to enable access into FreeNAS through AFP with the intent of disabling "DHCAST128" once my data was transferred.Ī couple of things that I have done to solve this so far: And then set up my new webcam, bluetooth keyboard and mouse, close up the system and begin customizing. Today's plan was to transfer data off of my FreeNAS box so I could retire it. Set my (2) WD Drives as storage drives (no issues) I installed Windows on the other OCZ drive (no issues) ![]() I installed Lion on one OCZ drive (no issues) Unfortunately, now I can not even get the BIOS Splash screen to show. I shut down in hopes that I could just boot back in. ![]() I was unable to do anything but the computer was still running. I worked on it for about 2 minutes and the screen went black. I came home from work today and woke my new hack from sleep with the connected USB keyboard. Any help would be very appreciated.ĬORSAIR Vengeance 16GB 240-Pin DDR3 SDRAM DDR3 1600 (4x4GB) This is my first Hack Build and I am a little lost. Building a CustoMac Hackintosh: Buyer's Guide
0 Comments
Read More
Leave a Reply. |